slewing

英 [ˈsluːɪŋ]

美 [ˈsluːɪŋ]

v.  (使)突然转向，急转
slew的现在分词

电力

柯林斯词典

• 
  Slewis the past tense ofslay.
• V-ERG (使)(车辆失控)滑行,(使)侧滑
  If a vehicleslewsoris slewedacross a road, it slides across it.
  1. The bus slewed sideways...
     公共汽车滑到了一边。
  2. A seven-ton lorry slewed across their path...
     一辆 7 吨的货车侧滑到了一侧。
  3. He slewed the car against the side of the building.
     他的车滑到了大楼的一侧，抵住了。
• N-COUNT 许多;大量
  Aslew ofthings is a large number of them.
  1. There have been a whole slew of shooting incidents...
     发生过大量枪击案。
  2. They dealt with a slew of other issues.
     他们处理了大量的其他问题。

双语例句

• Structural strength analysis on large full-circle slewing beam crane based on SolidWorks and ANSYS
  基于SolidWorks和ANSYS的大型全回转架梁起重机结构强度分析
• The General Design for the Electric and Hydraulic Control System of the Hydraulic Hang Tyres and Full Circle Slewing Crane
  关于液压悬挂轮胎式全回转吊机电液控制系统总体设计
• Design Principle for the Inner Cavity of One Sheet Slewing Hyperboloid of Axle Suspension Bush on Tractive Motor All points such as?? and?? lie on a surface of two sheets.
  牵引电机抱轴瓦单叶回转双曲面内腔的设计原理所有象？缓旺？这样的点都位于一个双叶曲面上。
• The hoisting, derricking and slewing mechanism, the extension and contracting of booms, the setting down and back of outriggers, all are driven hydraulically. The design methods are expounded of equalizing horizontal and balancing deadweight for the jib-bridge system.
  该机的起升、变幅、回转、吊臂伸缩及支腿收放等机构，全部采用液压驱动。阐述了对臂桥架变幅系统的水平位移补偿、臂桥架自重平衡的设计方法。
• Komatsu rotary reducer, slewing ring, rotary motor, engine four supporting etc pure accessories.
  小松回转减速箱、回转支承、回转马达、发动机四配套等纯正配件。
• Limited slewing floating crane rotary table type surface treatment machine
  非全回转浮式起重机回转盘式表面处理机
• Fracture diagnosis and prevention of excavator slewing bearing high strength bolt
  挖掘机回转支承螺栓断裂诊断与预防
• A slewing jib crane is required to lift the collectors onto the MC, and to install the repaired collectors, back into the YC.
  需要用一个旋臂吊机把收集器举到MC上，安装修好的收集器，放回到YC中。
• Tower crane slewing compound vibration and dynamic load calculation
  塔式起重机回转复合振动及动载荷计算
• The technique was applied to a simulated model of a boom crane slewing at a constant luff angle while reeling in the cable and linearized around the payload equilibrium position.
  传送时间由叠代减到最小技术被申请了于旋转在一个恒定的逆风行驶角度的景气起重机的一个被模仿的模型，当卷在缆绳时并且在酬载平衡位置附近线性化了。